Can't get Performer 405 to turn over now!

[Mighty Green Carpet Cleaning]

Is that it?

Sent from my SM-N910V using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

This one?

Sent from my SM-N910V using TMF Forums mobile app

 

[mrg.mrg.]

Nothing is showing up yet. Did you upload picture?

Sent from my E6853 using TMF Forums mobile app

 

[mrg.mrg.]

Not that. Let me see if I got a picture

Sent from my E6853 using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

Ok..sorry did it upload

Sent from my SM-N910V using TMF Forums mobile app

 

[mrg.mrg.]

This one

Sent from my E6853 using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

Is that on left or right side if you're facing machine

Sent from my SM-N910V using TMF Forums mobile app

 

[mrg.mrg.]

Left side if facing it.

Sent from my E6853 using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

Yes sorry that's the first picture I meant to send

Sent from my SM-N910V using TMF Forums mobile app

 

[mrg.mrg.]

Yeah that's it. Sometimes that goes bad. Or connections are loose.

Sent from my E6853 using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

So yes I got a new one of those from Jon Don today.
Today when Ara and I were working on this I touch the orange and white wire and it affected the machine stopping.
Sparked a little.
That's when he said let's wait to get there float in to make sure nothing is shorting out

Sent from my SM-N910V using TMF Forums mobile app

 

[Mighty Green Carpet Cleaning]

They were supposed to have my float valve assembly here today 2 day but I guess tomorrow

Sent from my SM-N910V using TMF Forums mobile app

 

[mrg.mrg.]

I see. I forgot how they used to by pass the float. I haven't done it in a while.

Sent from my E6853 using TMF Forums mobile app

 

[Todd the Cleaner]

I do here a click when I turn it
How would I remedy that...do u have a pic possibly?
Also I ordered float valve waste tank but if I'm running the machine
With overide turned to left I assume
Machine won't still shut off when tank gets full
Until I figure out the problem.
Right now I'm having to drain every couple rooms.
Thanks

Sent from my SM-N910V using TMF Forums mobile app

You should be able to clean at least 8-10 rooms without having to dump.

 

[mrg.mrg.]

So what happened??

Sent from my E6853 using TMF Forums mobile app

 

[SRD]

You should be able to clean at least 8-10 rooms without having to dump.

Wonder if the dema valve is bypassing to the water tank or his thermal valve on the water box is stuck open?

May have more than one thing going on with it

 

[mrg.mrg.]

Still nothing?

Sent from my E6853 using TMF Forums mobile app

 

[Lars]

I have been trying to follow along with the conversation here, I had the same issue on my 405 machine once. I'm trying to remember but I believe it was a relay switch and or a faulty sensor. Definitely electrical related. We used a bungy cord to help hold down the oil override switch also for a while.

 

[mrg.mrg.]

Me too....I need an update

Sent from my E6853 using TMF Forums mobile app

 

[JDARNOLD]

When you hold the override switch it overrides the oil pressure sensor and the high and low psi sensors. They are on the left side behind the panel. They are side by side. Take the wires loose and connect the wires together this bypasses the sensors. Now start the unit if it runs then it's one or both sensors. Low pressure is less than 50 psi high pressure over 1200 psi. So think about it did you run out of water on a job, or have the pressure turned up doing a T&G job before the problem started. If either sw is triggered being they want reset because they aren't triggered often.