Search results | TruckMount Forums #1 Carpet Cleaning Forums

Search results

  1. epservices

    Motorscrubber Ms13

    Jon Don has a cordless scrubber that resembles the Oreck Has anyone here used it before?
  2. epservices

    Carpet cleaner gunned down while cleaning

    He was shot in the back Even if he was carrying it would not have helped him
  3. epservices

    ELECTRIC TRUCK MOUNT

    Yes, that’s correct
  4. epservices

    Commercial Carpet Disaster

    If you have had that account since 2002, then you have been doing a lot of things right and your customer will work with you Maybe there is just a build up , residue from your pre spray over the years. Since most presprays are alkaline a good acid rinse might help, along with a good flush and...
  5. epservices

    Will carpet rinse drops corrode the marble surface?

    My rule of thumb is Always assume the chemical will damage the surface if it was not made for it
  6. epservices

    ELECTRIC TRUCK MOUNT

    Also one of the things I have observed is that the motors after installation does not match the numbers specified For example the 8.4. 13.8 amp does not get the 146.6 inches of lift I do not yet have a CFM gauge so I can’t measure it After placing two in parallel the lift should be the same but...
  7. epservices

    ELECTRIC TRUCK MOUNT

    Thank you Keep it Clean Series lowers CFM so I don’t see how it would increase in this case
  8. epservices

    ELECTRIC TRUCK MOUNT

    If one has two separate vac boxes with two vacs in parallel, would you get the series effect if you join the exhaust of one to the intake of another? It does seem logical but was wondering what setback (cons) I would face Thanks for your response
  9. epservices

    8.4 Lamb Motors

    The purpose of this forum is to inform, to seek advice , to give advice. It is to discuss different ideas . Those with a lot of experience are especially significant to this group We must be ready for our ideas to be challenged or questioned without feeling personally attacked I have gained a...
  10. epservices

    8.4 Lamb Motors

    Oh boy sometimes we confuse English with. American and Ebonics!
  11. epservices

    8.4 Lamb Motors

    Lol
  12. epservices

    8.4 Lamb Motors

    It would if these vacs were of the same capacity or if the smaller vacs were at the end(exhaust) of the bigger vacs But if they are all independently going into the waste tank , you will be wasting energy
  13. epservices

    8.4 Lamb Motors

    If your motor is not blowing air out of the exhaust or it is very weak then your motor is not doing any work
  14. epservices

    8.4 Lamb Motors

    At one time I was running six motors, with two 2stage in parallel, two three stage in series, and two 8.4s in parallel I then realized that something was off I tested an saw that on the weakest motors , I was sucking in air. The bigger motors were overpowering the weaker ones and it was having...
  15. epservices

    8.4 Lamb Motors

    Right now am working with 200 ft of hose with two 8.4s and a portable as a booster Am building the other box with the additional 8.4s
  16. epservices

    8.4 Lamb Motors

    There is something interesting about boosters. The vacs in the system must all be of the same capacity or you will lose cfm and lift. If you have vacs of different capacity anywhere in the system the higher capacity vacs will suck in air from the smaller capacity vacs , thereby reducing the...
  17. epservices

    8.4 Lamb Motors

    What will cause the waste tank to collapse, is it the lift or the cfm? I think if you raise the wand often enough you will prevent the collapse of the tank and also release the pressure in the tank for the APO to activate
  18. epservices

    8.4 Lamb Motors

    Can you give a heads up on the site where I can purchase the cfm gauge?
  19. epservices

    8.4 Lamb Motors

    Though it is true that at the end of working , by the time you walk back to shut everything down there is no water in the hose. It is while working I find that it takes about ten to fifteen seconds for all the water to be cleared into the waste tank . This might not seem to be a lot of time...
  20. epservices

    8.4 Lamb Motors

    Thanks!
  21. epservices

    8.4 Lamb Motors

    That is indeed amazing ! So in your opinion if you have four 8.4s , how would you set them up?
  22. epservices

    8.4 Lamb Motors

    I also think that using boosters at the entrance might increase cams but not lift. Also the boosters must be as strong as what is on the trailer/van or what is on the van will overpower the boaster and suck air through the vac motors If you can't feel air blowing against your hand when your...
  23. epservices

    8.4 Lamb Motors

    Men being courteous here is not an exception but is expected . We are here to discuss different ideas without giving offense So in that spirit , if the lift in a system will remain at the lift of the lowest vac motor, how then can one increase lift by adding a 5.7 vac to the back of an 8.4 ...
  24. epservices

    8.4 Lamb Motors

    And Jimsteam because the system will have the lift of the lowest vac , how will it increase the lift on 8.4 vac motors?
  25. epservices

    8.4 Lamb Motors

    How would that affect the CFM Jimsteam?