Recent content by Mas

  1. M

    2 inch swivel wand

    Good morning to you all TMFers, I’m looking for a used of course not abused, 2” Swivel wand. I’m in Santa Barbara CA. Let me know if any one has one that wants to let it go for a reasonable price! Thanks,, Masood
  2. M

    Hydramaster Titan 875.

    Good morning, I was wondering if you can give me some guidance Whether or not to buy A used hydramaster 875 with 3900 hours on it for $8000 I’ve used Prochem 405 and couple of blue lines for years, never owned hydramasters. I’ve been hurt buying used but reluctant to continue to do so, based on...
  3. M

    2004 Prochem performer 405 A15 motor keeps bogging and shutting down.

    Thank you so much for such a detailed instruction I did spray carb cleaner in and around it’s housing but no change in RPM, I used 2 bottles, also twisted air mixture screw up and down to see if any changes but not a whole lot.i have an old mechanic neighbor who works on small engines That maybe...
  4. M

    2004 Prochem performer 405 A15 motor keeps bogging and shutting down.

    I was busy working and fine tuning my other TM BL thermal vortec But I’ll look into it soon.thank you both,,
  5. M

    2004 Prochem performer 405 A15 motor keeps bogging and shutting down.

    Hey Jim, thank you so much for such a quick reply! I’ll look into it for crack and hose air leaks,, Have a great day!
  6. M

    2004 Prochem performer 405 A15 motor keeps bogging and shutting down.

    Hello dear TMFers out there, I’ve been haggling with my main equipment the 405 shutting down on me, I have a feeling it’s related to the carburator. Strange is that when I pull my choke all the way out it stays on and keeps going.ive used cleaners but didn’t help much! Could it be the speed...
  7. M

    Blue line vortec problem

    Does anyone out there have an extra Ecu for my blueline TWII vortec #38900438B ? That seems to be the problem. I borrowed one from another machine to see if that fixes the malfunction, and there it was, the answer to my problem! Thanks,,
  8. M

    Blue line vortec problem

    Hi Jim, so,, here’s what happened I pulled out the in-line hose to the Throttlebody/MAF sensor Opened the butterfly wing inside there just a little and jammed a thin piece of toothpick to keep the wing open, then put the hose back on there, now I can run it in low speed for a long time...
  9. M

    Blue line vortec problem

    That sounds like a good plan and what I’ve already been doing,, I know this old small engine mechanic who is willing to look into it ! Thanks for your help,, Masood.
  10. M

    Blue line vortec problem

    Pump is good filter is new but not too confident about the fuel pressure regulator. Thank you for your help,, Masood
  11. M

    Blue line vortec problem

    I put a bucket, disconnected the fuel line and dropped it in there, then cranked it and I saw the bucket filling up just enough to rule that out,, Thanks for your help! Masood.
  12. M

    Blue line vortec problem

    i Think it’s a kill switch, just unsure which one!
  13. M

    Blue line vortec problem

    I pulled out the hose that thank you for your help, but I’m not ready to take that drastic of action at this moment yet! I like the idea of HE, it’s safer and cleaner but not as Hot, that’s for sure,,
  14. M

    Blue line vortec problem

    Firstly I do appreciate your response, I talked with Scott over at sapphire and he suggested undoing the main wire to bypass all kill switches and I did. The “mechanic” who claimed to be a specialist Had the van for 2 weeks couldn’t figure it out! I changed the MAF sensor but No go,, So,, I’m...
  15. M

    Blue line vortec problem

    Hello All I picked up a used blueline thermal wave 2 with a Vortech engine, I bought it as is hoping I could spend a few hundred bucks to get it started. But after spending money on mechanics and parts back in square 1, The machine runs for five seconds then shuts down, is there anyone out...