Recent content by Conalnugent | TruckMount Forums #1 Carpet Cleaning Forums

Recent content by Conalnugent

  1. C

    Prochem blazer plus water pump belt removal

    That's great. I will check this out this evening or tomorrow morning.
  2. C

    Prochem blazer plus water pump belt removal

    Yup have taken that into concideration in my travels. The waste tank switch.... Its clicking as it should. I also tried starting it with it disconnected and connected and various combinations of wires on and off. Is there a way of testing it with a multimeter to see its working right?? The high...
  3. C

    Prochem blazer plus water pump belt removal

    Only got it. It briefly ran for about 5 minutes then cut out throwing the main breaker. It was suggested to me it might be the waste tank float switch but the engine is getting fuel but no spark. After watching a few lawnmower guys on YouTube I'm testing to see if its the kill wire to the coils...
  4. C

    Prochem blazer plus water pump belt removal

    That's it off. Slacked the pump as much as I could then as you said walked the belt off. Means I could get access to the coils. Now have disconnected the kill wires. Time to build up what needs be and test it. I suspect its either the kill wire is at fault or the coils themselves. But getting...
  5. C

    Prochem blazer plus water pump belt removal

    Thanks jdarnold. That will do lovely. Just finishing up breakfast so will try that ASAP.
  6. C

    Prochem blazer plus water pump belt removal

    I need to get the belt off to get the red engine cover off. Can I just manually turn the engine and pull off the belt? Or do I need to loosen something and if I do need to loosen something I assume unbolting the actual engine might be the best bet to allow the belt to come off?? Any words of...
  7. C

    Prochem blazer 1000 psi rebuild help

    After some extensive time on YouTube I think I might have found a plausible fix. My battery is dead but will borrow the battery out of my van to test the theory out.
  8. C

    Prochem blazer 1000 psi rebuild help

    OK so wanted to start the engine to get the exhaust manifold bolts to the heat exchanger heated up. Engine still not firing. Turning fine, pumping fuel but no spark. Tried every combo of plugging un plugging wires from the float switch still no joy. Difference this time as to when it orginally...
  9. C

    Prochem blazer 1000 psi rebuild help

    Pump oil topped up. So next chore was to get the exhaust heat exchanger out. I don't have a blow torch or impact gun to do the bolts. There seized solid. So taking advise from a mechanic friend, I will plumb all back up and run engine to temperature to heat the seized bolts from the exhaust...
  10. C

    Prochem blazer 1000 psi rebuild help

    Oil drain found and draining. Wasn't really rocket science figuring it out. So will get it topped up. This evenings job will be getting the heat exchangers out. Will give some good access then for cleaning.
  11. C

    Prochem blazer 1000 psi rebuild help

    OK. So got the blower sorted out. Found a manual online and help of a blower expert over in the states. Next job is the water pump. The fill level window is at the back of the pump. Just about can see it with a little mirror. But question..... How much oil does the pump take and where does it...
  12. C

    Prochem blazer 1000 psi rebuild help

    Right, so decided to service the tm before any further investigation if trying to run it. So am doing the following. Engine oil, spark plugs, rocker cover gaskets, oil filter, fuel filter, air filter, blower oil and pump oil. Quick question, how much oil does the blower and water pump take?
  13. C

    Prochem blazer 1000 psi rebuild help

    Don't know. Only had it running for about 20 minutes before it cut out so never tested that. What Ive been advised to do next is make sure its getting spark and fuel. Take plugs out and check for spark and disconnect fuel pump turn it over and see if its pumping. Apparently if both ain't...
  14. C

    Prochem blazer 1000 psi rebuild help

    How would I go about checking it is OK?
  15. C

    Prochem blazer 1000 psi rebuild help

    Looks good to me. What would be the next port of call to check?