We all know that theory is one thing, reality is another. In theory our 405 should have a stronger vacuum and drying capabilty than our Legend,...

A rather strange problem. Intermittent heat. Sometimes it runs hot pushing 230 and beyond while Im working, other times it wont even pass 180. ...

Someone suggested to me that they put warm water in the freshwater tank to help get the heat up. I replied that i wouldnt advise it due to the fact...

I have noticed over the last 60 days my chemical injection does not operate correctly. This unit is a prochem blazer. Most of the time, I have to...

working on a 100a and noticed its not getting full throttle, when the throttle is pulled out it only throttles to 1/4 maybe a tad over that. its...

My blower belt for the Prochem Peak went on Friday, but this time I was prepared. I have been keeping track of the hours, temp conditions etc for...

That big garnder denver blower is tough to move even a 1/4 inch with all the bolts off, the plug is on the bottom and you cant get to it! How do...

This is retarded. The main intake hose right on top of the waterbox lid. I need a prybar to get into it if I need to check the float or clean the...

Hi. I'm new to this business. I have a Prochem Legend SE that is not producing any heat at all. The water is going in to the dump tank at an...

I have a prochem everest that is about 5 years old. How hot should the water be while running a sx-12 at 1000psi? It will stay about 230 degrees with...

I am posting this for All Clean Extreme, Justin believes his Prochem Legend has a bad fuel pump, He wants to know what is the pressure output of the...

I have an old Bridgepiont Lancer (made by Prochem) the water pressure is sometimes very good and fully adjustable at the pressure regulator although...

I need the manual for a bruin. I have several issues and i need to be able to stay with specs.

We have a prochem everest just had it serviced 2 weeks ago and their tech is away for training now and will not be back till next week.The service...

Hello, Own and operate a Bridgepoint Lancer made by Pro Chem. 2500 hours and never had a problem. This last week the engine started fluttering....

Where other then jon-don or interlink is the cheap place to buy a Radiator for prochem performer 405 ??????????????:AddEmoticons04259:

How many hours should I have to change the blower oil? Its not an easy job on a Prochem Peak. Im at about 1300hrs now. Maybe I dont need to...

I have a blazer plus with an 18 hp engine, It is a B&S. I read the manuals already but I can't find how many quarts of il I have to add. Anybody...

Does anyone know the oil filter for this machine. I went to napa last week and he said "it'll be here by 2:00", so I went back, nope. So I went again...

I have a Bruin II that is constantly bypassing water into the waste tank. The temp. control microswitch, temperature gauge, solenoid, bypass valve,...

Does anyone know exactly what make and model the carburetor on the Performer 405's Nissan A12 motor is? $500+ for a new one and I'm looking for...

Oily water spits out of the exhaust if I have been running it on low idle to do furniture. It is not from the waste tank being too full, I checked...

The other day I was using my truckmount to clean a pool. I know, sounds crazy but it makes doing an Acid Wash so much easier. I was running the...

Hey there,,,,, just saw my flowmeter on my legend has a crack in the top, I will be replacing it soon and noticed jondon and the sorts wants 68...

i hate briggs and stratton motors! this blazer has less than 2000 hours and we are going on the 4th motor....oil changed religously every 50 hours...

10 mins into my first job this morning the machine just quit. Went out and checked gas level in van, ok, did it overheat? Nope, then tried to start...

Im having problems with my ProChem Legend XL The machine will not heat the water to its fullest capabilities and the pressure gauge fails to read...

Does anyone know where I can get one?

I am looking at a 2001 Prochem Legend SE with 600 hours on it, in a van for $4000.00 Sounds like to good of a deal. Going to look at it in a few...

I have a Saber machine that will not stay running. I have replaced the battery, cleaned the connections. I also replaced the voltage regulator but...

had to change the bearings on the blower in my prochem everest today. knowing i cannot get prochem oil by my next job; what alternative oil would...

ok just today the 150 prochem i have started to smoke out the chimney with the burner on or off its not kero smell it smells like an old go cart the...

Ok guys may be simple may not be, I need to find out that is going on with the Legend, It is producing great heat however it is shutting the machine...

am i missing something?? i loosened the 6 bolts on the bottom...the 4 bolts holding the vacuum to the machine and also loosened the bolt holding the...

I don't know much about the mechanics of a TM. So what are these called and is it a problem that the back one is starting to corrode? ...

I have an older Legend that is letting water bypass all the time. I have changed the bypass valve, I have also put a solenoid from one of my other...

Im looking to buy a new thrmostat for my 405 at my local parts store. Does anyone know a part number or model number that I need to use. I'm trying...

i have an old prochem bruin with a broken heat exchange and prochem no longer makes them. i need to find options quickly. will be having it taken...

How do I test it?? Is there any sensor I need to check?? I don't think I'm getting enough heat .... Prochem Bear

anyone have any experience or comments on a 2004 prochem everest (44 hp nissan, 2000 hrs.)? use butler now and am thinking of trying a slide in. ...

:eek: i have recently bought a prochem150 when i got it, it had a clogged burner so i switched to a little giant propane system and that works great...

Hi to everyone, I am a new member here and was wondering if anybody could help me with a problem I am having. I have a Prochem Blazer and cleaning...

Hi, I recently bought this truckmount prochem performer 405 w/nissan engine. I've only used this machine 6 times since I purchase it. Yesterday I was...

Prochem blazer XL-water box Having never owned or seen a blazer I have had a look at the manual of the above machine and it appears that it has a...

i have a used legend i got about 5 months ago. its very hard too start i got a stronger battery. it works some times. but most of the time i have too...

i just got a used prochem legend tm i think its 94. it has a pump out but when i turn it on nothing happens.i never had one so i dont know if im...

I think I have a crack in the heat exchange, I have small amounts of water comming out of the exhaust, I did not think it froze since Ialready have...

Hi everyone, I have a Blazer plus that is not heating enough. It is a two stage using vacuum exhaust and engine exhaust. The engine heat exchanger...

How much oil does the engine for a Peak take?